Water heaters, or geysers, are as delicate as other electronic devices. Although manufacturers make the best parts to withstand constant heating and cooling, it is important to keep in mind that even the most durable parts can be damaged by continuous pressure. We will be discussing tips and tricks for water heater maintenance to extend its lifespan despite regular expansion and contraction due to heating and cooling.
Here are some things to remember when installing a geyser or water heater
- There is plenty of space around the geyser.
Remember to leave enough space between the water heater and walls when installing it. The technician will not be able service the water heater properly if there is not enough space. To ensure a proper installation, hire certified technicians.
It should also be easy to access if you need it repaired or serviced. Although some people place the geyser on top of the toilet for easier access, it actually makes it difficult for technicians to reach the device. It is better to place it on a wall with nothing below the geyser, away from damp areas such as the toilet, shower, or bathtub. You or anyone else can access it easily with a small stool.
- Place the water heater at an appropriate height
Experts recommend that the geyser be installed at least 1.8m (6 feet) above the ground. This will ensure that your water pressure is adequate and that you have a strong hot water flow from the tap, rather than a trickle.
- Switches and electrical connections:
Make sure that the geyser has a Miniature Circuit Breaker, (MCB), that cuts off electricity in the event of power fluctuations. This will reduce the chances of a short circuit in your water heater. Keep the switch at an appropriate height so that children are not in direct contact with it. However, you should not be able to reach it from a high place where adults or children may have problems.
We now know the best precautions for gas hot water installation in omaha. Let’s take a look at some maintenance tips to help maintain it.
Water heater maintenance tips
- The geyser should not be left on for prolonged periods of time
Most people prefer to leave the geyser on for longer periods of time, especially in the morning. It is generally believed that everyone will need warm water before going to work or school. Keeping the geyser running will help save time. While this may have been true once upon a while, today’s geysers heat water in just 5 minutes. It is better to turn the geyser off for 5 minutes before you use it, and not wait half an hour. Your heater’s life expectancy can be extended by regular water heater maintenance. Water heater repair service professionals are also available.
- Lowering the temperature can help you save more electricity
It is vital to maintain your water heater. You will also save electricity! You can set the temperature lower so that water reaches the desired temperature quicker. A lower temperature will mean that the geyser has to work less, which will increase its lifespan. Warm water is better than hot water, which will help reduce the chance of accidental burns. Families with small children should lower the thermostat. It is crucial to maintain your hot water heater in order to have hot water throughout winter.
- Before winter, make sure to inspect the anode rod in the tank
Larger geysers contain an anti-corrosion rod within the tank. This rod attracts rust, and other impurities in water. It prevents the tank from corroding or becoming rusted. It corrodes every few years due to this.
Experts recommend that the anode rod be checked every three years to ensure that the outer layer of magnesium is not corroded and 6 inches or more remains of the inner steel core. If this is the case, the rod should be replaced. If the rod is covered with whitish calcium particles (which happens when water is hard), or if its thickness has fallen to less than half an inch, it must be replaced.
- Make sure the pressure release valve is working properly
At least once per year, check that the temperature and pressure release valves work. This can be checked by releasing the pressure several times. Leakage of the relief valve at your water heater can cause serious damage. It is easy to drain the water from your water heater and then remove the tube. Then, replace the valve.
- Pay attention to the plug
Your switch will occasionally spark due to power fluctuations or low-capacity wiring. The higher electricity wattage will cause burn marks to your plug’s pins.
It is better to use new plugs and sockets, which have been wired properly and plugged in, to prevent future short-circuits. An MCB switch is a better choice than a regular plug and will prevent short-circuits from occurring. You can also make sure that the geyser is turned on only when it is needed and then turn it off after it has finished.
- Replacing the outlet and inlet pipes made of plastic with metal is a good idea.
Metal inlet and outlet pipes are better than standard plastic ones. They are also more heat resistant than the ones that come with geysers. Make sure to inspect the joints every so often. If you notice rust or hard water deposits around the joints, it’s time to replace the outlet or inlet pipe.
- Do an annual maintenance
Last but not least, if you don’t have the experience to maintain a geyser and want to avoid problems with your water heater, it is better to hire an expert than to try to fix it yourself. They can also help you clean your water heater.
